Your shopping cart is empty!
ASTM International, 03/01/2018
Publisher: ASTM
File Format: PDF
$32.00$65.00
Published:01/03/2018
Pages:12
File Size:1 file , 160 KB
Note:This product is unavailable in Russia, Ukraine, Belarus
1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.
Title of Specification
ASTM DesignationA
Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes
A209/A209M
Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
A213/A213M
Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
A249/A249M
Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes
A250/A250M
Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service
A268/A268M
Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A269/A269M
Seamless and Welded Austenitic and Ferritic/Austenitic Stainless Steel Sanitary Tubing
A270/A270M
Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service
A334/A334M
Welded Austenitic Stainless Steel Feedwater Heater Tubes
A688/A688M
Austenitic Stainless Steel Tubing for Breeder Reactor Core Components
A771/A771M
Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service
A789/A789M
Seamless and Welded Ferritic Stainless Steel Feedwater Heater Tubes
A803/A803M
Seamless Austenitic and Martensitic Stainless Steel Duct Tubes for Liquid Metal-Cooled Reactor Core Components
A826/A826M
High-Frequency Induction Welded, Unannealed, Austenitic Steel Condenser Tubes
A851
Welded Austenitic Alloy Steel Boiler, Superheater, Condenser, and Heat Exchanger Tubes with Textured Surface(s)
A1098/A1098M
1.2 In the case of conflict between a requirement of a product specification and a requirement of this general requirements specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this general requirements specification and a more stringent requirement of the purchase order, the purchase order shall prevail.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods and Practices for Emulsified Asphalts
$33.00 $67.00
Standard Test Method for Failure in Sewn Seams of Woven Fabrics
$28.00 $56.00
Standard Test Method for Relative Permittivity (Dielectric Constant) and Dissipation Factor of Polymer-Based Microwave Circuit Substrates
$32.00 $65.00
Standard Guide for The Installation of Operable Partitions
$30.00 $60.00
