ASTM A1063/A1063M-11a

1.1 This specification covers steel sheet, produced by the Twin-Roll Cast Process (see Appendix X2) and zinc-coated (galvanized) by the hot-dip process in coils and cut lengths.

Note 1 - See Appendix X2 for a description of the Twin-Roll Cast process.

1.2 The product is produced in various zinc coating weights [masses] or coating designations as shown in Table 1.

1.3 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M unless otherwise provided herein.

1.4 The product is available in a number of designations, grades and classes and in the two following general categories that are designed to be compatible with different application requirements.

1.4.1 Steels with mandatory chemical requirements and typical mechanical properties.

1.4.2 Steels with mandatory chemical requirements and mandatory mechanical properties.

1.5 This material is available in the following sizes:

1.5.1 Thickness - up to 0.078 in. [2.0 mm]

1.5.2 Width - up to 79 in. [2000 mm]

1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

1.7 This specification is applicable to orders in either inch-pound units (as A1063) or SI units (as A1063M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.

1.8 Unless the order specifies the "M" designation (SI units), the product shall be furnished to inch-pound units.

1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Weight [Mass] of Coating Requirements^{A, B, C}

Note - Use the information provided in 8.1.2 to obtain the approximate coating thickness from the coating weight [mass].

		Minimum Requirement
		Triple-Spot Test		Single-Spot Test
Inch-Pound Units
Type	Coating Designation	Total Both Sides, oz/ft²	One Side, oz/ft²	Total Both Sides, oz/ft²
Zinc	G01C	no minimum	no minimum	no minimum
	G30	0.30	0.10	0.25
	G40	0.40	0.12	0.30
	G60	0.60	0.20	0.50
	G90	0.90	0.32	0.80
	G100	1.00	0.36	0.90
	G115	1.15	0.40	1.00
	G140	1.40	0.48	1.20
	G165	1.65	0.56	1.40
	G185	1.85	0.64	1.60
SI Units
Type	Coating Designation	Total Both Sides, g/m²	One Side, g/m²	Total Both Sides, g/m²
Zinc	Z001C	no minimum	no minimum	no minimum
	Z90	90	30	75
	Z120	120	36	90
	Z180	180	60	150
	Z275	275	94	235
	ASTM B111-98e2 Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock $30.00 $60.00 Add to Cart ASTM F3092-14 Standard Terminology Relating to Optical Fiber Sensing Systems $32.00 $65.00 Add to Cart ASTM D5467/D5467M-97(2010) Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam $30.00 $60.00 Add to Cart ASTM D6448-14 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils $30.00 $60.00 Add to Cart