• ASTM A358/A358M-15

ASTM A358/A358M-15

Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications

ASTM International, 09/01/2015

Publisher: ASTM

File Format: PDF

$31.00$62.00


Published:01/09/2015

Pages:9

File Size:1 file , 100 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This specification2 covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or high-temperature service, or both, or for general applications.

Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”

1.2 This specification covers the grades of alloy and stainless steel listed in Table 1. The selection of the proper grade and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered.

(A) New designation established in accordance with Practice E527 and SAE J1086.
(B) Choice of American Welding Society specification depends on the welding process used.
(C) Minimum carbon content of the filler metal shall be 0.040 mass %.
(D) In previous editions, S30600 was incorrectly shown as S01815.
(E) Common name, not a trademark, widely used, not associated with any one producer.
(F) These filler metals have a high nickel content and, therefore, lower creep strength than the parent metal at temperatures exceeding about 1470 °F [800 °C], and its resistance to sulphurous media is inferior in certain cases.

1.3 Five classes of pipe are covered as follows:

1.3.1 Class 1-Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed.

1.3.2 Class 2-Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required.

1.3.3 Class 3-Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed.

1.3.4 Class 4-Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal (see 6.2.2.1 and 6.2.2.2).

1.3.5 Class 5-Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed.

1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S6 are included as options to be specified when desired.

1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

More ASTM standard pdf

ASTM F2435-12

ASTM F2435-12

Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe

$29.00 $58.00

ASTM E1734-15

ASTM E1734-15

Standard Practice for Radioscopic Examination of Castings

$29.00 $58.00

ASTM E170-14

ASTM E170-14

Standard Terminology Relating to Radiation Measurements and Dosimetry

$30.00 $60.00

ASTM D2013/D2013M-12

ASTM D2013/D2013M-12

Standard Practice for Preparing Coal Samples for Analysis

$27.00 $54.00