Your shopping cart is empty!
ASTM International, 03/01/2012
Publisher: ASTM
File Format: PDF
$26.00$52.00
Published:01/03/2012
Pages:3
File Size:1 file , 71 KB
Note:This product is unavailable in Russia, Ukraine, Belarus
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1.
Designation No.
Nominal Tin Coating Weight [Mass] (Each Surface) lb/base box (g/m²)B
Minimum Average Coating Weight [Mass] (Each Surface Test Value) lb/base box (g/m²)B, C
5 (0.6/0.6)
0.025/0.025 (0.6/0.6)
0.02/0.02 (0.5/0.5)
10 (1.1/1.1)
0.05/0.05 (1.1/1.1)
0.04/0.04 (0.9/0.9)
15 (1.7/1.7)
0.075/0.075 (1.7/1.7)
0.06/0.06 (1.4/1.4)
20 (2.2/2.2)
0.10/0.10 (2.2/2.2)
0.08/0.08 (1.8/1.8)
25 (2.8/2.8)
0.125/0.125 (2.8/2.8)
0.11/0.11 (2.5/2.5)
50 (5.6/5.6)
0.25/0.25 (5.6/5.6)
0.23/0.23 (5.2/5.2)
75 (8.4/8.4)
0.375/0.375 (8.4/8.4)
0.35/0.35 (7.8/7.8)
100 (11.2/11.2)
0.50/0.50 (11.2/11.2)
0.45/0.45 (10.1/10.1)
1.1.1 Electrolytic tin-coated sheet is customarily available as commercial steel (CS); drawing steel (DS); deep drawing steel (DDS); extra deep drawing steel (EDDS), and structural steel (SS). The tin coating is available as unmelted or melted.
1.2 Limitations-This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M].
1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine
$30.00 $60.00
Standard Test Methods of Static Tests of Lumber in Structural Sizes
$49.00 $98.00
Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane
$27.00 $54.00
Standard Practice for Design of Amusement Rides and Devices
$57.00 $114.00
