• Your shopping cart is empty!

  • ASTM A74-05

ASTM A74-05

Standard Specification for Cast Iron Soil Pipe and Fittings

ASTM International, 06/01/2005

Publisher: ASTM

File Format: PDF

$47.00$94.00


Published:01/06/2005

Pages:44

File Size:1 file , 430 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification.

1.2.1 Pipe

Tables
Extra heavy, 21/ 2 ft (0.75 m), 31/2ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths 1, 2
Service, 21/2 ft (0.75 m), 31/2ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) 1, 2
Outside dimensions (for detailing) X1.1

1.2.2 Fittings

Tables
1/4 bends; long 1/4 bends 3, 4
1/4 bends, long low-hub 5
1/4 bends, low heel; high heel 6, 7
1/4 bends, short sweep; long sweep 8
1/4 bends, reducing long sweep 9
1/5 bends 10
1/6 bends 10
1/8 bends; long 1/8 bends 11
1/16 bends 11
Y branches 12, 13
Y branches, combination 1/8 bends, single 14
Y branches, combination 1/8 bends, double 14
Sanitary T branches, single 15
Sanitary T branches, double 15
Sanitary T branches, cleanout 16
Tapped sanitary T branches, single 17
Tapped sanitary T branches, double 17
T branches, single and double 18
Tapped T branches, single 19
Tapped T branches, double 19
T branches, cleanout 20
-45 offset fitting 21
Double hubs 22
Long double hubs 22
Reducers 23
Increasers 24, 25
P traps 26, 27
Deep seal P traps 28
Running traps 29
Screw plugs (brass) 30
Blind plugs 31
Iron-body ferrules 32
Side inlets Fig. 3
Closet bends 33
Tapping bosses 34
Reducing 1/4 bend SV 35
Combination Y and 1/8 bend 36
H branch fitting 37

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. Metric conversions in Tables 1 and 2 are to two decimal places; all other metric conversions are rounded to the nearest whole number.

More ASTM standard pdf

ASTM D4364-13

ASTM D4364-13

Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight

$32.00 $64.00

ASTM E2837-13

ASTM E2837-13

Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies

$32.00 $65.00

ASTM F2670-13

ASTM F2670-13

Standard Consumer Safety Specification for Infant Bath Tubs

$29.00 $58.00

ASTM C1577-13

ASTM C1577-13

Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD

$33.00 $67.00