• ASTM A888-18a

ASTM A888-18a

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

ASTM International, 11/15/2018

Publisher: ASTM

File Format: PDF

$47.00$94.00


Published:15/11/2018

Pages:59

File Size:1 file , 1.3 MB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.

1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2

1.3.1 Lengths:

 

Figures

EDP/ASA Identification Numbers
for Hubless Pipe

Fig. 1

10 ft (3.0 m) in sizes and 5 ft. (1.5 m)
11/2 , 2, 3, 4, 5, 6, 8,
10, 12, and 15 in.

Fig. 1, Fig. 2

Method of Specifying Fittings

Fig. 3

1.3.2 Fittings: 

More ASTM standard pdf

ASTM E803-91(2008)

ASTM E803-91(2008)

Standard Test Method for Determining the L/D Ratio of Neutron Radiography Beams

$30.00 $60.00

ASTM D49-83(1996)e1

ASTM D49-83(1996)e1

Standard Test Methods of Chemical Analysis of Red Lead

$25.00 $50.00

ASTM D3552-96(2007)

ASTM D3552-96(2007)

Standard Test Method for Tensile Properties of Fiber Reinforced Metal Matrix Composites

$30.00 $60.00

ASTM D3429-93(2007)

ASTM D3429-93(2007)

Standard Test Method for Solubility of Fixed Gases in Low-Boiling Liquids

$30.00 $60.00

Quarter Bend

Fig. 5

Quarter Bend, Reducing

Fig. 6

Quarter Bend, with Side Opening

Fig. 7

Quarter Bend, with Heel Opening

Fig. 8

Quarter Bend, Tapped

Fig. 9

Quarter Bend, Double

Fig. 10

Quarter Bend, Long

Fig. 11

Short Sweep

Fig. 12

Long Sweep

Fig. 13

Long Sweep, Reducing

Fig. 14

Fifth Bend

Fig. 15

Sixth Bend

Fig. 16

Eighth Bend

Fig. 17

Eighth Bend, Long

Fig. 18

Sixteenth Bend

Fig. 19

Sanitary Tee

Fig. 20

Sanitary Tee with Side Opening

Fig. 21

Sanitary Tee with 2 in. Side Opening R or L/R and L

Fig. 22

Sanitary Tee, New Orleans Special with Side Opening

Fig. 23

Sanitary Tee with 45° Side Openings and New Orleans

Fig. 24

Sanitary Special Tee Tapped

Fig. 25

Sanitary Tapped Tee, Horizontal Twin

Fig. 26

Sanitary Tapped Tee, Double Vertical

Fig. 27

Y Branch

Fig. 28

Y Branch, Double

Fig. 29

Y Branch, Upright

Fig. 30