Your shopping cart is empty!
ASTM International, 09/01/2021
Publisher: ASTM
File Format: PDF
$42.00$85.00
Published:01/09/2021
Pages:59
File Size:1 file , 1.6 MB
Note:This product is unavailable in Russia, Ukraine, Belarus
1.1''This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2''The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.
1.3''This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.2
1.3.1''Lengths:
''
Figures
EDP/ASA Identification Numbers for Hubless Pipe
Fig. 1
10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11/2'', 2, 3, 4, 5, 6, 8, 10, 12, and 15 in.
Fig. 1, Fig. 2
Method of Specifying Fittings
Fig. 3
1.3.2''Fittings:''
Quarter Bend
Fig. 5
Quarter Bend, Reducing
Fig. 6
Quarter Bend, with Side Opening
Fig. 7
Quarter Bend, with Heel Opening
Fig. 8
Quarter Bend, Tapped
Fig. 9
Quarter Bend, Double
Fig. 10
Quarter Bend, Long
Fig. 11
Short Sweep
Fig. 12
Long Sweep
Fig. 13
Long Sweep, Reducing
Fig. 14
Fifth Bend
Fig. 15
Sixth Bend
Fig. 16
Eighth Bend
Fig. 17
Eighth Bend, Long
Fig. 18
Sixteenth Bend
Fig. 19
Sanitary Tee
Fig. 20
Sanitary Tee with Side Opening
Fig. 21
Sanitary Tee with 2 in. Side Opening R or L/R and L
Fig. 22
Sanitary Tee, New Orleans Special with Side Opening
Fig. 23
Sanitary Tee with 45'' Side Openings and New Orleans
Fig. 24
Sanitary Special Tee Tapped
Fig. 25
Sanitary Tapped Tee, Horizontal Twin
Fig. 26
Sanitary Tapped Tee, Double Vertical
Fig. 27
Y Branch
Fig. 28
Y Branch, Double
Fig. 29
Y Branch, Upright
Standard Practice for Enumeration of Mycobacteria in Metalworking Fluids by Direct Microscopic Counting (DMC) Method
$27.00 $55.00
Standard Specification for Double-Twisted Hexagonal Mesh Gabions and Revet Mattresses (Metallic-Coated Steel Wire or Metallic-Coated Steel Wire With Poly(Vinyl Chloride) (PVC) Coating)
$31.00 $63.00
Standard Test Method for Hydraulic Activity of Slag Cement by Reaction with Alkali
Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components
$34.00 $69.00