• Your shopping cart is empty!

  • ASTM A999/A999M-23

ASTM A999/A999M-23

Standard Specification for General Requirements for Alloy and Stainless Steel Pipe

ASTM International, 09/01/2023

Publisher: ASTM

File Format: PDF

$31.00$63.00


Published:01/09/2023

Pages:12

File Size:1 file , 340 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This specification2 covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.
Title of Specification ASTM Desig-
nation3     Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes A312/A312M Seamless and Welded Steel Pipe for Low-Temperature
Service and Other Applications with Required Notch
Toughness A333/A333M Seamless Ferritic Alloy-Steel Pipe for High Temperature
Service A335/A335M Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless
Steel Pipe for High-Temperature Service and General
Applications A358/A358M Carbon and Ferritic Alloy Steel Forged and Bored Pipe for
High-Temperature Service A369/A369M Seamless Austenitic Steel Pipe for High-Temperature
Service A376/A376M Welded Large Diameter Austenitic Steel Pipe for Corrosive
or High-Temperature Service A409/A409M Centrifugally Cast Ferritic Alloy Steel Pipe for
High-Temperature Service A426/A426M Centrifugally Cast Austenitic Steel Pipe for High-
Temperature Service A451/A451M Centrifugally Cast Iron-Chromium-Nickel High-Alloy
Tubing for Pressure Application at High
Temperatures A608/A608M Welded, Unannealed Austenitic Stainless Steel Tubular
Products A778/A778M Seamless and Welded Ferritic/Austenitic
Stainless Steel Pipe A790/A790M Single- or Double-Welded Austenitic Stainless Steel Pipe A813/A813M Cold-Worked Welded Austenitic Stainless Steel Pipe A814/A814M Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe
for Corrosive Environments A872/A872M Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric
Fusion Welded with Addition of Filler Metal A928/A928M Spray-Formed Seamless Austenitic Stainless Steel Pipes A943/A943M Spray-Formed Seamless Ferritic/Austenitic Stainless Steel Pipe A949/A949M Austenitic Chromium-Nickel-Silicon Alloy Steel Seamless
and Welded Pipe A954
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units apply unless the "M" designation (SI) of the product specification is specified in the order.
Note 1: The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as "nominal diameter," "size," "nominal bore," and "nominal size."
1.4 The following precautionary statement pertains only to the test method portion, Section 21, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

More ASTM standard pdf

ASTM D4017-22

ASTM D4017-22

Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method

$28.00 $57.00

ASTM D7234-22

ASTM D7234-22

Standard Test Method for Pull-Off Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers

$28.00 $57.00

ASTM E930-18

ASTM E930-18

Standard Test Methods for Estimating the Largest Grain Observed in a Metallographic Section (ALA Grain Size)

$26.00 $52.00

ASTM D910-14

ASTM D910-14

Standard Specification for Aviation Gasolines

$30.00 $60.00