• ASTM B111/B111M-09

ASTM B111/B111M-09

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

ASTM International, 04/01/2009

Publisher: ASTM

File Format: PDF

$33.00$67.00


Published:01/04/2009

Pages:11

File Size:1 file , 140 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified: (Warning-Mercury is a definite health hazard in use and disposal. (See 12.1.))

Copper or
Copper
Alloy
UNS No.
Previously
Used
Designation
Description
C10100 OFE Oxygen-free electronic
C10200 OFA Oxygen-free without residual deoxidants
C10300 . . . Oxygen-free, extra low phosphorus
C10800 . . . Oxygen-free, low phosphorus
C12000 DLPA Phosphorized, low residual phosphorus
C12200 DHPA Phosphorized, high residual phosphorus
C14200 DPAA Phosphorized, arsenical
C19200 . . . Phosphorized, 1 % iron
C23000 . . . Red Brass
C28000 . . . Muntz Metal
C44300 . . . Admiralty Metals, B, C, and D
C44400
C44500
C60800 . . . Aluminum Bronze
C61300 . . . . . .
C61400 . . . Aluminum Bronze, D
C68700 . . . Aluminum Brass, B
C70400 . . . 95-5 Copper-Nickel
C70600 . . . 90-10 Copper-Nickel
C70620 . . . 90-10 Copper-Nickel-Welding Grade
C71000 . . . 80-20 Copper-Nickel
C71500 . . . 70-30 Copper-Nickel
C71520 . . . 70-30 Copper-Nickel-Welding Grade
C71640 . . . Copper-nickel-iron-manganese
C72200 . . . . . .

A Designations listed in Classification B 224.

1.2 Units - The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact    equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

More ASTM standard pdf

ASTM F2709-19

ASTM F2709-19

Standard Test Method for Determining a Measured Nameplate Recovery Rate of Stationary Oil Skimmer Systems

$25.00 $50.00

ASTM F148-13(2019)

ASTM F148-13(2019)

Standard Test Method for Binder Durability of Cork Composition Gasket Materials

$21.00 $42.00

ASTM D6494-22

ASTM D6494-22

Standard Test Method for Determination of Asphalt Fume Particulate Matter in Workplace Atmospheres as Benzene Soluble Fraction

$27.00 $54.00

ASTM C443-19

ASTM C443-19

Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

$29.00 $58.00