Your shopping cart is empty!
ASTM International, 11/01/2018
Publisher: ASTM
File Format: PDF
$34.00$69.00
Published:01/11/2018
Pages:11
File Size:1 file , 100 KB
Note:This product is unavailable in Russia, Ukraine, Belarus
1.1 This specification2 covers forgings of:
Alloy Type
UNS Number(s)
Fe-Ni-Cr-Mo-N
N08367
Low-carbon Cr-Ni-Fe-N
R20033
Low-carbon Ni-Cr-Mo
N06035, N06058, N06059, N06044
Low-carbon Ni-Cr-Mo-Cu
N06200
Low-carbon Ni-Cr-Mo-W
N06686
Low-carbon Ni-Fe-Cr-Mo-Cu
N08031, N08034
Low-carbon Ni-Mo-Cr
N10276, N06022, N10362
Low-carbon Ni-Mo-Cr-Ta
N06210
Ni
N02200
Ni-Co-Cr-Si
N12160
Ni-Cr-Al
N06699
Ni-Cr-Co-Mo
N06617
Ni-Cr-Fe
N06600, N06603, N06690
Ni-Cr-Fe-Al
N06025
Ni-Cr-Fe-Si
N06045
Ni-Cr-Mo-Nb
N06625
Ni-Cr-Mo-Si
N06219
Ni-Cr-Mo-W
N06110
Ni-Cr-W-Mo
N06230
Ni-Cu
N04400
Ni-Fe-Cr
N08120, N08800, N08810, N08811
Ni-Fe-Cr-Mo-Cu
N08825
Ni-Fe-Cr-W
N06674
Ni-Mo
N10665, N10675, N10629
Ni-Mo-Cr-Fe
N10242, N10624
1.1.1 The nickel-iron-chromium alloys are UNS N08120, UNS N08800, UNS N08810, and UNS N08811. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100°F (593°C). Alloys UNS N08810, N08120, and UNS N08811 are normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and are annealed to develop controlled grain size for optimum properties in this temperature range.
1.1.2 Nickel-iron-chromium-tungsten alloy UNS N06674 is normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and is annealed to develop optimum properties in this temperature range.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM Book of Standards Volume 8.01: Plastics (I): D256 - D3159
$107.00 $215.54
Standard Practice for Surface Wettability of Coatings, Substrates and Pigments by Advancing Contact Angle Measurement
$28.00 $56.00
Standard Guide for Oil Spill Dispersant Application Equipment: Single-point Spray Systems
$26.00 $52.00
Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant
$29.00 $58.00
