• ASTM B952/B952M-12

ASTM B952/B952M-12

Standard Specification for Zinc Alloys in Ingot Form for Spin Casting

ASTM International, 05/01/2012

Publisher: ASTM

File Format: PDF

$26.00$52.00


Published:01/05/2012

Pages:3

File Size:1 file , 70 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This specification covers zinc alloys in ingot form for remelting for the manufacture of Spin Castings as specified and designated, as shown in Table 1. Seven alloy compositions are specified, designated as follows:

Common Traditional UNS
Spin Casting Alloy SC-A ... ...
Spin Casting Alloy SC-B ... ...
Spin Casting Alloy SC-C ... ...
Spin Casting Alloy SC-D HJ10 ...
Spin Casting Alloy SC-E HJ20 ...
Spin Casting Alloy SC-F HJ40 ...
ZA-73 ... ...

1.2 Zinc alloys #2, #3, #5, and ZA-8 specified in Specification B240 are also used in the spin casting process.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

TABLE 1 Chemical and North American Color Code Requirements

Alloy SC-A Alloy SC-B Alloy SC-C ZA-73 Alloy SC-D Alloy SC-E Alloy SC-F
Color CodeA
ElementB
Aluminum 3.9-4.3 3.9-4.3 3.4-4.6 7.7-8.0 3.2-3.8 3.2-3.8 3.25-3.75
Magnesium 0.1-0.2 0.4-0.6 0.4-0.43 0.02-0.03 0.15-0.30 0.45-0.75 0.45-4.75
Copper 2.6-2.9 2.7-3.3 1.3-1.4 3.0-3.3 1.2-1.8 2.5-3.25 4.25-4.75
Iron, max 0.035 0.035 0.10 0.075 0.035 0.075 0.035
Lead, max 0.004 0.004 0.015 0.005 0.004 0.005 0.004
Cadmium, max 0.0030 0.0030 0.005 0.003 0.003 0.003 0.003
Tin, max 0.0015 0.0015 0.005 0.002 0.002 0.003 0.002
Nickel, max ... ... 0.02 ... . . . 0.02 . . .
Zinc Remainder Remainder Remainder Remainder Remainder Remainder Remainder

A Per Practice B908.

B For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures, used in expressing the specific limit in accordance with the rounding procedure prescribed in Practice E29.

More ASTM standard pdf

ASTM G152-05

ASTM G152-05

Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials

$29.00 $58.00

ASTM D1890-05

ASTM D1890-05

Standard Test Method for Beta Particle Radioactivity of Water

$30.00 $60.00

ASTM D3718-85a(2005)

ASTM D3718-85a(2005)

Standard Test Method for Low Concentrations of Chromium in Paint by Atomic Absorption Spectroscopy

$26.00 $52.00

ASTM B381-05

ASTM B381-05

Standard Specification for Titanium and Titanium Alloy Forgings

$30.00 $60.00