• ASTM D5302-01

ASTM D5302-01

Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions

ASTM International, 11/10/2001

Publisher: ASTM

File Format: PDF

$62.00$124.00


Published:10/11/2001

Pages:121

File Size:1 file , 2.7 MB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method is commonly referred to as the Sequence VE test² and has been correlated with vehicles used in stop-and-go service prior to 1988, particularly with regard to sludge and varnish formation and valve train wear. It is one of the test methods required to evaluate oils intended to satisfy the API SJ performance category.

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in parentheses when combined with inch-pound units. Some of the figures and forms have identical numerical designations, but with the letter M following the numerical designation: these are alternative figures and forms that contain SI units.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.7, 7.8.9.6, 7.8.13, 7.10.2, 7.10.3.2(c), 8.3.4.2, 8.4.4.3, 8.4.5.2, 9.3.4.4, 9.6.1.2, 12.1.1.5, 12.1.4.5, 12.2.1, 12.2.1.5, Fig. A3.6, and Annex A8.

1.4 Table of Contents:

Section
Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus-General Description 6
Apparatus-The Test Engine 7
Sequence VE Test Engine Parts Kit 7.1
Required New Engine Parts 7.2
Reusable Engine Parts 7.3
Specially Fabricated Engine Parts 7.4
Special Engine Measurement and Assembly Equipment 7.5
Miscellaneous Engine Components-Preparation 7.6
Solvents and Cleansers Required 7.7
Assembling the Test Engine-Preparations 7.8
Assembling the Test Engine-Installations 7.9
Engine Installation on the Test Stand 7.10
Engine Fluids-Supply/Discharge Systems 8
Intake Air 8.1
Fuel 8.2
Engine Oil 8.3
Coolants 8.4
Measurement Instrumentation 9
Temperatures 9.1
Pressures 9.2
Flow Rates 9.3
Fuel Consumption 9.4
Speed and Load 9.5
Exhaust Gas 9.6
Miscellaneous Laboratory Equipment 10
Test Stand Calibration 11
Verification 11.1
Unacceptable Calibration Tests 11.2
Test Stand Modifications 11.3
Reference Oil Accountability 11.4
Test Numbering System 11.5
Procedure 12
Pre-Test Procedure 12.1
Engine Operating Procedure 12.2
Periodic Measurements and Functions 12.3
Special Maintenance Procedures 12.4
Diagnostic Data Review 12.5
End of Test Procedure 12.6
Interpretation of Results 13
Parts Rating Area-Environment 13.1
Sludge Ratings 13.2
Varnish Ratings 13.3
Clogging 13.4
Sticking 13.5
Wear Measurements 13.6
Assessment of Test Validity 14
Average Exhaust Gas NO X Levels 14.2
Used Oil Analyses 14.3
Blowby Flow Rate 14.4
Intake Manifold Vacuum 14.5
Fuel Consumption Rate 14.6
Oil Consumption 14.7
Report 15
Report Format 15.1
Special Forms for Automated Data Acquisition 15.2
Standard Report 15.3
Calibration Test Report 15.4
Precision and Bias 16
Precision 16.1
Bias 16.2
ANNEXES
Special Service Tools for the Test Engine A1
External Oil Heat Exchanger Cleaning Technique A2
Detailed Specifications and Photographs of Apparatus A3
Engine Part Number Listing A4
Operational Data Log Sheets A5
Rating Worksheets A6
Final Report Forms and Photographs A7
Safety Precautions A8
Automatic Data Acquisition A9
Oakite 811 Monitoring Program A10
Test Precision-Reference Oils A11
Control Chart Technique for Severity Adjustment A12
Statistical Equations for Mean and Standard Deviation A13
Data Dictionary A14
One-half Millimetre Oversize Piston Modifications A15
Required Inspections and Operations for Reuse of Cylinder Heads A16
APPENDIXES
Engine Measurement Sheets X1
Sources of Materials and Information X2
Analysis of Phillips "J" Fuel (Batch 26) X3
Theoretical Exhaust Gas Relationships-Phillips "J" Fuel X4
Description of Scott Quarterly Gas Audit Service X5

More ASTM standard pdf

ASTM D3657-03(2014)

ASTM D3657-03(2014)

Standard Specification for Zipper Dimensions

$27.00 $54.00

ASTM E340-00(2006)

ASTM E340-00(2006)

Standard Test Method for Macroetching Metals and Alloys

$33.00 $67.00

ASTM D4869/D4869M-16a

ASTM D4869/D4869M-16a

Standard Specification for Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing

$27.00 $54.00

ASTM C1304-95(2001)

ASTM C1304-95(2001)

Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials

$26.00 $52.00