Your shopping cart is empty!
ASTM International, 01/01/2016
Publisher: ASTM
File Format: PDF
$24.00$48.00
Published:01/01/2016
Pages:10
File Size:1 file , 290 KB
Note:This product is unavailable in Russia, Ukraine, Belarus
1.1 These test methods cover the determination of the Impact Value (IV) of a soil either in the field or a test mold, as follows:
1.1.1 Field Procedure A-Determination of IV alone, in the field.
1.1.2 Field Procedure B-Determination of IV and water content, in the field.
1.1.3 Field Procedure C-Determination of IV, water content, and dry density, in the field.
1.1.4 Mold Procedure-Determination of IV of soil compacted in a mold, in the lab.
1.2 The standard test method, using a 4.5 kg (10 lbm) hammer, is suitable for, but not limited to, evaluating the strength of an unsaturated compacted fill, in particular pavement materials, soils, and soil-aggregates having maximum particle sizes less than 37.5 mm (1.5 in.).
1.3 By using a lighter 0.5 kg (1.1 lbm) or 2.25 kg (5 lbm) hammer, this test method is applicable for evaluating lower strength soils such as fine grained cohesionless, highly organic, saturated, or highly plastic soils having a maximum particle size less than 9.5 mm (0.375 in.), or natural turfgrass.
1.4 By using a heavier 10 kg (22 lbm) or 20 kg (44 lbm) hammer, this test method is applicable for evaluating for harder materials at the top end the scales or beyond the ranges of the standard and lighter impact soil testers.
1.5 By performing laboratory test correlations for a particular soil using the 4.5 kg (10 lbm) hammer, IV may be correlated with an unsoaked California Bearing Ratio (CBR) or may be used to infer percentage compaction.
1.6 The values stated SI are to be regarded as the standard. The values stated in parentheses are given for information only.
1.7 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.8 For purposes of comparing, a measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits.
1.8.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user's objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1: The equipment and procedures contained in this test method are similar to those developed by B. Clegg in the 1970s at the University of Western Australia, Nedlands, Australia. Impact Value is also commonly known as Clegg Impact Value (CIV).
Standard Practice for Performing Accelerated Outdoor Weathering of Materials Using Concentrated Natural Sunlight
$38.00 $76.00
Standard Specification for High Purity p-Xylene
$25.00 $50.00
Standard Specification for Apparatus For Microdetermination of Carbon and Hydrogen in Organic and Organo-Metallic Compounds
$24.00 $48.00
Standard Test Method for Determination of Reference Temperature, To, for Ferritic Steels in the Transition Range
$41.00 $83.00
