• ASTM D5967-04

ASTM D5967-04

Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

ASTM International, 11/01/2004

Publisher: ASTM

File Format: PDF

$33.00$67.00


Published:01/11/2004

Pages:19

File Size:1 file , 330 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method is commonly referred to as the Mack T-8. This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading).

1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.

1.3 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are generally shown in parentheses when combined with SI units, and vice versa.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.

1.5 A Table of Contents follows:

Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Methods 4
Significance and Use 5
Apparatus 6
General Description 6.1
The Test Engine 6.2
Mack Test Engine 6.2.1
Engine Cooling System 6.2.2
Engine Oil System 6.2.3
Auxiliary Oil System 6.2.4
Crankcase Aspiration 6.2.5
Blowby Meter 6.2.6
Air Supply and Filtration 6.2.7
Fuel Supply 6.2.8
Intake Manifold Temperature Control 6.2.9
Engine Fluids 7
Test Oils 7.1
Test Fuel 7.2
Engine Coolant 7.3
Cleaning Materials 7.4
Preparation of Apparatus at Rebuild 8
Cleaning of Parts 8.1
Valves, Seats, Guides, and Springs 8.2
Cylinder Liner, Piston, and Piston Ring Assembly 8.3
Injectors and Injection Pump 8.4
Assembly Instructions 8.5
Measurements 8.6
Laboratory and Engine Test Stand Calibration/Non-Reference Requirements 9
Calibration Frequency 9.1
Calibration Reference Oils 9.2
Test Numbering 9.3
New Laboratories and New Test Stands 9.4
Calibrated Laboratories and Test Stands 9.5
Calibration Test Acceptance 9.6
Failing Calibration Tests 9.7
Non-Reference Oil Test Requirements 9.8
Procedure 10
Pretest Procedure 10.1
Engine Start-Up 10.2
Engine Shutdown 10.3
Test Cycle 10.4
Oil Addition/Drain 10.5
Oil Samples 10.6
Oil Consumption Calculations 10.7
Fuel Samples 10.8
Periodic Measurements 10.9
Blowby 10.10
Centrifugal Oil Filter Mass Gain 10.11
Oil Filter ∇P Calculation 10.12
Post Test 10.13
Inspection of Fuel and Oil During Test 11
Oil Inspection 11.1
Fuel Inspections 11.2
Oil Consumption 11.3
Report 12
Reporting Test Results 12.1
Deviations from Test Operational Limits 12.2
Electronic Transmission of Test Results 12.3
Plots of Operational Data 12.4
Precision and Bias 13
Precision 13.1
Bias 13.2
Keywords 14
Annexes
Report Forms Annex A1
Sensor Locations Annex A2
Kinematic Viscosity At 100°C For Test Method D 5967 Samples Annex A3
Enhanced Thermal Gravimetric Analysis (TGA) Procedure Annex A4
Procurement of Test Materials Annex A5
Safety Precautions Annex A6
Data Dictionary Annex A7
T-8E Extended Length Test Requirements Annex A8
T-8A Abbreviated Length Test Requirements Annex A9

More ASTM standard pdf

ASTM F2042-00(2005)

ASTM F2042-00(2005)

Standard Guide for Silicone Elastomers, Gels, and Foams Used in Medical Applications Part II - Crosslinking and Fabrication

$29.00 $58.00

ASTM D1282-05

ASTM D1282-05

Standard Test Method for Resistance to Airflow as an Indication of Average Fiber Diameter of Wool Top, Card Sliver, and Scoured Wool

$30.00 $60.00

ASTM D6319-00a(2005)

ASTM D6319-00a(2005)

Standard Specification for Nitrile Examination Gloves for Medical Application

$26.00 $52.00

ASTM D2103-05

ASTM D2103-05

Standard Specification for Polyethylene Film and Sheeting

$30.00 $60.00