• ASTM D6201-03

ASTM D6201-03

Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation

ASTM International, 07/10/2003

Publisher: ASTM

File Format: PDF

$43.00$86.00


Published:10/07/2003

Pages:29

File Size:1 file , 410 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method coves an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels. This test uses a Ford Ranger 2.3 L four-cylinder engine. The following details the procedure, hardware, and operations used for this test.

1.2 The ASTM Test Monitoring Center (TMC) is responsible for engine test stand certification as well as issuance of information letters after test method modifications are approved by Subcommittee D02.A and Committee D02. Users of this test method shall request copies of recent information letters from the TMC to ensure proper conduct of the test method.

1.3 The values stated in SI units are to be regarded as the standard. Approximate inch-pound units are shown in parenthesis for information.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine applicability of regulatory limitations prior to use. Specific precautionary statements are given throughout this test method.

1.4 This test method is arranged as follows:

Subject Section
Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus 6
Laboratory Facilities 6.1
Test Stand Laboratory Equipment 6.2
Test Engine Hardware 6.3
Special Measurement and Assembly Equipment 6.4
Reagents and Materials 7
Fuel 7.1
Engine Oil and Assembly Lubricant 7.2
Engine Coolant 7.3
Solvents and Cleaners 7.4
Fuel Injector Test Fluid 7.5
Valve Lapping Compound 7.6
Crushed Walnut Shells 7.7
Desiccant 7.8
Hazards 8
Specific Hazards 8.1
Reference Fuel 9
Reference Base Fuel Batch Approval Process 9.1
Fuel Batch Analyses 9.2
Fuel Batch Shipment and Storage 9.3
Preparation of Apparatus 10
Test Stand Preparation 10.1
Engine Block Preparation 10.2
Preparation of Miscellaneous Engine Components 10.3
Cylinder Head Preparation 10.4
Cylinder Head Assembly 10.5
Cylinder Head Installation 10.6
Final Engine Assembly 10.7
Calibration 11
Test Stand Calibration 11.1
Instrumentation Calibration 11.2
Test Procedure 12
Pretest Procedure 12.1
Engine Operating Procedure 12.2
Periodic Measurements and Functions 12.3
End of Test Procedures 12.4
Determination of Test Results 13
Post-test Intake Valve Weighing Procedure 13.1
Photographs of Parts - General 13.2
Induction System Rating 13.3
Determination of Test Validity - Engine Conformance 13.4
Final Test Report 14
Standard Report 14.1
Data Acquisition Summary Report 14.2
Photographs of Specific Parts 14.3
Precision and Bias 15
Precision 15.1
Bias 15.2
Keywords 16
Annexes
Detailed Specifications and Photographs of Apparatus Annex A1
Engine Part Number Listing Annex A2

More ASTM standard pdf

ASTM D570-98(2010)e1

ASTM D570-98(2010)e1

Standard Test Method for Water Absorption of Plastics

$26.00 $52.00

ASTM E161-00

ASTM E161-00

Standard Specification for Precision Electroformed Sieves

$26.00 $52.00

ASTM D5570/D5570M-10

ASTM D5570/D5570M-10

Standard Test Method for Water Resistance of Tape and Adhesives Used as Box Closure

$26.00 $52.00

ASTM D3424-09

ASTM D3424-09

Standard Practice for Evaluating the Relative Lightfastness and Weatherability of Printed Matter

$30.00 $60.00