ASTM D6709-08

1.1 This test method covers the evaluation of automotive engine oils (SAE grades 5W, 10W, 20, 30, 40, and 50, and multiviscosity grades) intended for use in spark-ignition gasoline engines. The test procedure is conducted using a carbureted, spark-ignition Cooperative Lubrication Research (CLR) Oil Test Engine (also referred to as the Sequence VIII test engine in this test method) run on unleaded fuel. An oil is evaluated for its ability to protect the engine and the oil from deterioration under high-temperature and severe service conditions. The test method can also be used to evaluate the viscosity stability of multiviscosity-graded oils. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D 4485.

1.2 Correlation of test results with those obtained in automotive service has not been established. Furthermore, the results obtained in this test are not necessarily indicative of results that will be obtained in a full-scale automotive spark-ignition or compression-ignition engine, or in an engine operated under conditions different from those of the test. The test can be used to compare one oil with another.

1.3 The values stated in SI units are to be regarded as standard, except for (1) volume which is given in the metric, but non-SI, litre, (2) certain tube measurements which are given in inch-pound units, (3) cylinder bore and stroke in both SI and inch-pound units (the inch-pound being the standard) and (4) piston displacement given in metric (non-SI) and inch-pound units (the inch-pound being the standard). In respect to (3) and (4) the inch-pound units are shown first and the SI units in parentheses.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are provided throughout this test method.

1.5 This test method is arranged as follows:

Subject		Section
Introduction
Scope		1
Referenced Documents		2
Terminology		3
Summary of Test Method		4
	Before Test Starts	4.1
	Power Section Installation	4.2
	Engine Operation (Break-in)	4.3
	Engine Operation (Test/Samples)	4.4
	Stripped Viscosity	4.5
	Test Completion (BWL)	4.6
Significance and Use		5
	Evaluation of Automotive oils	5.1
	Stay in Grade Capabilities	5.2
	Correlation of Results	5.3
	Use	5.4
Apparatus		6
	Test Engineering, Inc.	6.1
	Fabricated or Specially Prepared Items	6.2
	Instruments and Controls	6.3
	Procurement of Parts	6.4
Reagents and Materials		7
	Reagents	7.1
	Cleaning Materials	7.2
	Expendable Power Section-Related Items	7.3
	Power Section Coolant	7.4
	Reference Oils	7.5
	Test Fuel	7.6
Test Oil Sample Requirements		8
	Selection	8.1
	Inspection	8.2
	Quantity	8.3
Preparation of Apparatus		9
	Test Stand Preparation	9.1
	Conditioning Test Run on Power Section	9.2
	General Power Section Rebuild Instructions	9.3
	Reconditioning of Power Section After Each Test	9.4
Calibration		10
	Power Section and Test Stand Calibration	10.1
	Instrumentation Calibration	10.2
	Calibration of AFR Measurement More ASTM standard pdf ASTM B138-96 Standard Specification for Manganese Bronze Rod, Bar and Shapes (Withdrawn 2001) $25.00 $50.00 Add to Cart ASTM D5367-16 Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted $27.00 $54.00 Add to Cart ASTM A630-16a Standard Test Methods for Determination of Tin Coating Weights for Electrolytic Tin Plate $29.00 $58.00 Add to Cart ASTM D4122-96ae1 Standard Practice for Carbon Black-Evaluation of an Industry Reference Black $25.00 $50.00 Add to Cart