• ASTM D6923-08

ASTM D6923-08

Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine - ;Caterpillar 1R Test Procedure

ASTM International, 10/15/2008

Publisher: ASTM

File Format: PDF

$50.00$101.00


Published:15/10/2008

Pages:64

File Size:1 file , 1.1 MB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method covers stressing an engine oil under modern high-speed diesel operating conditions and measures the oil's deposit control, lubrication ability, and resistance to oil consumption. It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine.

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. Being an engine test method, this test method does have definite hazards that require safe practices (see Appendix X2 on Safety).

1.4 The following is the Table of Contents:

More ASTM standard pdf

ASTM B886-03(2008)

ASTM B886-03(2008)

Standard Test Method for Determination of Magnetic Saturation (Ms) of Cemented Carbides

$26.00 $52.00

ASTM Volume 14.02:2015

ASTM Volume 14.02:2015

ASTM Book of Standards Volume 14.02: General Test Methods; Forensic Psychophysiology; Forensic Sciences; Terminology; Conformity Assessment; Statistical Methods; Nanotechnology; Forensic Engineering; Manufacture of Pharmaceutical Products

$106.00 $213.65

ASTM E345-16

ASTM E345-16

Standard Test Methods of Tension Testing of Metallic Foil

$24.00 $48.00

ASTM D5900-15a

ASTM D5900-15a

Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM)

$29.00 $58.00

Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus and Installation 6
Intake Air System 6.2.1
Exhaust System 6.2.2
Fuel System 6.2.3
Oil Consumption System 6.2.4
Engine Oil System 6.2.5
Engine Coolant System 6.2.6
Engine Instrumentation 6.2.7
Reagents and Materials 7
Oil Samples 8
Preparation of Apparatus 9
General Engine Assembly Practices 9.1
Complete Engine Inspection 9.2
Copper Component 9.3
Engine Lubricant System Flush 9.4
Engine Piston Cooling Jet 9.5
Engine Measurements and Inspections 9.6
Cylinder Head 9.7
Valve Guide Bushings 9.8
Fuel Injector 9.9
Piston and Rings 9.10
Cylinder Liner 9.11
Compression Ratio 9.12
Engine Timing 9.13
Engine Coolant System Cleaning Procedure 9.14
Calibration and Standardization 10
Test Cell Instrumentation 10.1
Instrumentation Standards 10.2
Coolant Flow 10.3
Fuel Injectors 10.4
Air Flow 10.5
Intake Air Barrel 10.6
Fuel Filter 10.7
Oil Scale Flow Rates 10.8
Test Stand Calibration 10.9
Re-calibration Requirements 10.9.1
Extending Test Stand Calibration Period 10.9.2
Test Run Numbering 10.10
Humidity Calibration Requirements 10.11
Calibration of Piston Deposit Raters 10.12
Procedure 11
Engine Break-in Procedure 11.1
Cool-down Procedure 11.2
Warm-up Procedure 11.3
Shutdowns and Lost Time 11.4
Periodic Measurements 11.5
Engine Control Systems 11.6
Engine Coolant 11.6.1
Engine Fuel System 11.6.2
Engine Oil Temperature 11.6.3
Exhaust Pressure 11.6.4
Intake Air 11.6.5
Post-Test Procedures 11.7