• ASTM D6984-07

ASTM D6984-07

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine

ASTM International, 05/01/2007

Publisher: ASTM

File Format: PDF

$47.00$94.00


Published:01/05/2007

Pages:47

File Size:1 file , 1.2 MB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening, varnish deposition, oil consumption, as well as engine wear. Such oils include both single viscosity grade and multiviscosity grade oils that are used in both spark-ignition, gasoline-fueled engines, as well as in diesel engines.

Note 1 - Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.

1.2 The values stated in SI or other units are to be regarded as the standard. The values given in parentheses are provided for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

1.4 This test method is arranged as follows:

More ASTM standard pdf

ASTM B150/B150M-12

ASTM B150/B150M-12

Standard Specification for Aluminum Bronze Rod, Bar, and Shapes

$30.00 $60.00

ASTM F813-07(2012)

ASTM F813-07(2012)

Standard Practice for Direct Contact Cell Culture Evaluation of Materials for Medical Devices

$30.00 $60.00

ASTM E2518-06

ASTM E2518-06

Standard Specification for Cargo Bed Cover, Type IV (M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/M1082, 5 Ton MTV Trailer)

$32.00 $65.00

ASTM F750-87(2012)

ASTM F750-87(2012)

Standard Practice for Evaluating Material Extracts by Systemic Injection in the Mouse

$26.00 $52.00

Subject Section
Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus 6
Laboratory 6.1
Drawings 6.2
Specified Equipment 6.3
Test Engine 6.4
Engine Parts 6.4.1
Engine Speed and Load Control 6.5
Sequence IIIF Fluid Conditioning Module 6.6
Engine Cooling System 6.6.1
Flushing Tank 6.7
Coolant Mixing Tank 6.8
Condenser Cooling Systems 6.9
Engine Oil-Cooling System 6.10
Fuel System 6.11
Induction Air Supply Humidity, Temperature, and Pressure 6.12
Temperature Measurement 6.13
Thermocouple Location 6.13.1
Air-to-Fuel Ratio Determination 6.14
Injector Flow Testing 6.14.1
Exhaust and Exhaust Back Pressure Systems 6.15
Blowby Flow Rate Measurement 6.16
Pressure Measurement and Sensor Location 6.17
Reagents and Materials 7
Test Fuel 7.1
Engine and Condenser Coolant 7.2
Coolant Additive 7.3
Coolant Preparation 7.4
Pre-Test Cleaning Materials 7.5
Sealing and Anti-seize Compounds 7.6
Test Oil Sample Requirements 8
Preparation of Apparatus 9
Condenser Cleaning 9.1
Intake Manifold Cleaning 9.3
Cleaning of Engine Parts (other than the block and heads) 9.4
Engine Block Cleaning 9.5
Cylinder Head Cleaning 9.6
Engine Build-up Procedure 9.7
General Information 9.7.1
Special Parts 9.7.2
Hardware Information 9.7.3
Fastener Torque Specifications and Torquing Procedures 9.7.4
Parts Replacement 9.8
Engine Block Preparation 9.9
Piston Fitting and Numbering 9.10
Piston Ring Fitting 9.10.1
Pre-Test Camshaft and Lifter Measurements 9.11
Camshaft Bearing Installation 9.12
Camshaft Installation 9.13
Main Bearings 9.14
Crankshaft Installation 9.14.1
Main Bearing Cap Installation 9.14.2
Crankshaft Sprocket 9.15
Camshaft Sprocket and Timing Chain 9.16
Crankshaft End Play 9.17
Piston Pin Installation 9.18
Piston Installation 9.18.1
Harmonic Balancer 9.19
Connecting Rod Bearings 9.20
Engine Front Cover 9.21
Coolant Inlet Adapter 9.22
Oil Dipstick Hole 9.23
Oil Pan 9.24
Cylinder Head Assembly 9.25
Adjustment of Valve Spring Loads 9.26
Cylinder Head Installation 9.27
Hydraulic Valve Lifters 9.28
Pushrods 9.29
Valve Train Loading 9.30
Intake Manifold 9.31
Rocker Covers 9.32
Water Inlet Adapter 9.33
Condenser 9.34
Coolant Outlet Adapter 9.35
External Oil Cooling System 9.36
Oil Sample Valve 9.37
Ignition System 9.38
Throttle Body 9.39
Accessory Drive Units 9.40
Exhaust Manifolds, Water-Cooled 9.41
Engine Flywheel 9.42
Pressure Checking of Engine Coolant System 9.43
Lifting of Assembled Engines 9.44
Mounting the Engine on the Test Stand 9.45
External Cooling System Cleaning 9.46
Engine Coolant Jacket Cleaning (Flushing) 9.47
Coolant Charging 9.48
Test Oil Charging 9.49
Engine Oil Pump Priming 9.50
Calibration 10
Laboratory and Engine Test Stand Calibration 10.1
Testing of Reference Oils 10.2