• ASTM F1802-04

ASTM F1802-04

Standard Test Method for Performance Testing of Excess Flow Valves

ASTM International, 04/01/2004

Publisher: ASTM

File Format: PDF

$29.00$58.00


Published:01/04/2004

Pages:7

File Size:1 file , 81 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method covers a standardized method to determine the performance of excess flow valves (EFVs) designed to limit flow or stop flow in thermoplastic natural gas service lines.

1.2 All tests are intended to be performed using air as the test fluid. Unless otherwise stated, all flow rates are reported in standard cubic feet per hour of 0.6 relative density natural gas.

1.3 The test method recognizes two types of EFV. One type, an excess flow valve-bypass (EFVB), allows a small amount of gas to bleed through (bypass) after it has tripped, usually as a means of automatically resetting the device. The second type, an excess flow valve-non bypass (EFVNB), is intended to trip shut forming an essentially gas tight seal.

1.4 The performance characteristics covered in this test method include flow at trip point, pressure drop across the EFV, bypass flow rate of the EFVB or leak rate through the EFVNB after trip, and verification that the EFV can be reset.

1.4.1 Gas distribution systems may contain condensates and particulates such as organic matter, sand, dirt, and iron compounds. Field experience has shown that the operating characteristics of some EFVs may be affected by accumulations of these materials. The tests of Section were developed to provide a simple, inexpensive, reproducible test that quantifies the effect, if any, of a uniform coating of kerosene and of kerosene contaminated with a specified amount of ferric oxide powder on an EFV's operating characteristics.

1.5 Excess flow valves covered by this test method will normally have the following characteristics: a pressure rating of up to 125 psig (0.86 MPa); a trip flow of between 200 and 2500 ft³/h (5.66 and 70.8 m³/h) at 10 psig (0.07 MPa); a minimum temperature rating of 0F(-18C), and a maximum temperature rating of 100F (38C).

1.6 The EFVs covered by this test method shall be constructed to fit piping systems no smaller than 1/2CTS and no larger than 11/4IPS, including both pipe and tubing sizes.

1.7 Tests will be performed at 67 10F (19.4 5.5C). Alternative optional test temperatures are 100 10F (37.7 5.5C) and 0 10F (-18 5.5C). All flow rates must be corrected to standard conditions.

1.8 This test method was written for EFVs installed in thermoplastic piping systems. However, it is expected that the test method may also be used for similar devices in other piping systems.

1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see Section .

More ASTM standard pdf

ASTM F659-98e1

ASTM F659-98e1

Standard Specification for Skier Goggles and Faceshields

$29.00 $58.00

ASTM D6247-98

ASTM D6247-98

Standard Test Method for Analysis of Elemental Content in Polyolefins By X-Ray Fluorescence Spectrometry

$25.00 $50.00

ASTM E2360-04(2010)

ASTM E2360-04(2010)

Specification for Cryptolaemus montrouzieri Mulsant (Coleoptera: Coccinellidae) (Withdrawn 2019)

$25.00 $50.00

ASTM F375-89(2010)

ASTM F375-89(2010)

Standard Specification for Integrated Circuit Lead Frame Material

$25.00 $50.00