• ASTM F3348-21a

ASTM F3348-21a

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM International, 08/01/2021

Publisher: ASTM

File Format: PDF

$32.00$64.00


Published:01/08/2021

Pages:7

File Size:1 file , 240 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1''This specification covers plastic press insert fittings with factory assembled stainless steel press sleeves incorporating 3 view holes and a tool locator ring. These fittings are for use with cross-linked polyethylene (PEX) tubing in nominal sizes ³/8'', 1/2'', ³/4'', 1, 11/4'', 11/2'', and 2 that meet the requirements for Specification F876 or F3253 and for use with polyethylene of raised temperature (PE-RT) tubing in nominal sizes ³/8'', 1/2'', ³/4'', 1, 11/4'', 11/2'', and 2 that meet the requirements of Specification F2769. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180'''''F (82'''''C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and sleeves.

1.1.1''When used with PEX tubing in accordance with Specification F876, the fittings covered by this specification are intended for use in, but not limited to, residential and commercial, hot- and cold-potable water distribution systems, water service lines, reclaimed water, fire protection, radiant heating and cooling systems, hydronic distribution systems, snow and ice melting systems, geothermal ground loops, district heating, turf conditioning, compressed air distribution and building services pipe.

1.1.2''When used with PEX tubing in accordance with Specification F3253, the fittings covered by this specification are intended for use in residential and commercial hydronic heating and cooling systems.

1.1.3''When used with PE-RT tubing in accordance with Specification F2769, the fittings covered by this specification are intended for use in residential and commercial, hot- and cold-potable water distribution systems.

1.2''Units'''The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3''This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4''This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

More ASTM standard pdf

ASTM D2968-95(2008)

ASTM D2968-95(2008)

Standard Test Method for Med and Kemp Fibers in Wool and Other Animal Fibers by Microprojection

$26.00 $52.00

ASTM F2291-08

ASTM F2291-08

Standard Practice for Design of Amusement Rides and Devices

$45.00 $91.00

ASTM E777-17a

ASTM E777-17a

Standard Test Method for Carbon and Hydrogen in the Analysis Sample of Refuse-Derived Fuel

$34.00 $68.00

ASTM F924-90(2022)

ASTM F924-90(2022)

Standard Test Method for Resistance to Puncture of Cushioned Resilient Floor Coverings

$25.00 $50.00