ASTM F406-11a

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playing accommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388. This specification does not cover inflatable products.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1 - This consumer safety specification includes the following sections:

Title	Section
Scope	1
Referenced Documents	2
ASTM Standards	2.1
Federal Regulations	2.4
Terminology	3
Definitions of Terms Specific to This Standard	3.1
Conspicuous	3.1.2
Cord	3.1.3
Corner Post	3.1.4
Dropside/Dropgate	3.1.5
Dynamic Load	3.1.6
Fabric	3.1.7
Foldable Side or End	3.1.8
Key Structural Elements	3.1.9
Manufacturer's Recommended Use Position	3.1.10
Mattress	3.1.11
Mesh	3.1.12
Mesh/Fabric Crib	3.1.13
Nonpaper Label	3.1.16
Occupant	3.1.17
Paper Label	3.1.18
Play Yard	3.1.19
Protrusion	3.1.20
Rigid Sided Crib	3.1.21
Seam	3.1.22
Static Load	3.1.23
Stationary Side	3.1.24
Structural Failure	3.1.26
Calibration and Standardization	4
General Requirements	5
Corner Posts	5.1
Scissoring, Shearing, or Pinching	5.6
Latching and Locking Mechanisms	5.8
Openings	5.9
Protective Components	5.10
Labeling	5.11
Stability	5.12
Cord/Strap Length	5.13
Coil Springs	5.14
Entrapment in Accessories	5.15
Mattress	5.16
Mattress for Rigid Sided Products	5.17
Protrusions	5.18
Record Keeping	5.20
Performance Requirements for Rigid Sided Units	6
Crib-Side Height	6.2
Spacing of Unit Components	6.3
Hardware	6.4
Fasteners	6.5
Construction and Finishing	6.6
Requirements for Cutouts	6.7
Plastic Teething Rail	6.11
Cyclic Test	6.12
Side(s) or End(s) Latch Testing, or Both	6.13
Dropgate Latch Testing	6.13.1
More ASTM standard pdf ASTM E208-06 Standard Test Method for Conducting Drop-Weight Test to Determine Nil-Ductility Transition Temperature of Ferritic Steels $33.00 $67.00 Add to Cart ASTM F2621-06 Standard Practice for Determining Response Characteristics and Design Integrity of Arc Rated Finished Products in an Electric Arc Exposure $29.00 $58.00 Add to Cart ASTM E384-06 Standard Test Method for Microindentation Hardness of Materials $43.00 $86.00 Add to Cart ASTM C1097-06a Standard Specification for Hydrated Lime for Use in Asphalt Cement or Bituminous Pavements $26.00 $52.00 Add to Cart