ASTM F406-12

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playing accommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388. This specification does not cover inflatable products.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1 - This consumer safety specification includes the following sections:

Title	Section
Scope	1
Referenced Documents	2
ASTM Standards	2.1
Federal Regulations	2.4
Terminology	3
Definitions of Terms Specific to This Standard	3.1
Conspicuous	3.1.2
Cord	3.1.3
Corner Post	3.1.4
Dropside/Dropgate	3.1.5
Dynamic Load	3.1.6
Fabric	3.1.7
Foldable Side or End	3.1.8
Key Structural Elements	3.1.9
Manufacturer's Recommended Use Position	3.1.10
Mattress	3.1.11
Mesh	3.1.12
Mesh/Fabric Crib	3.1.13
Nonpaper Label	3.1.16
Occupant	3.1.17
Paper Label	3.1.18
Play Yard	3.1.19
Protrusion	3.1.20
Rigid Sided Crib	3.1.21
Seam	3.1.22
Static Load	3.1.23
Stationary Side	3.1.24
Structural Failure	3.1.26
Calibration and Standardization	4
General Requirements	5
Corner Posts	5.1
Scissoring, Shearing, or Pinching	5.6
Latching and Locking Mechanisms	5.8
Openings	5.9
Protective Components	5.10
Labeling	5.11
Stability	5.12
Cord/Strap Length	5.13
Coil Springs	5.14
Entrapment in Accessories	5.15
Mattress	5.16
Mattress for Rigid Sided Products	5.17
Protrusions	5.18
Record Keeping	5.20
Performance Requirements for Rigid Sided Units	6
Crib-Side Height	6.2
Spacing of Unit Components	6.3
Hardware	6.4
Fasteners	6.5
Construction and Finishing	6.6
Requirements for Cutouts	6.7
Plastic Teething Rail	6.11
Cyclic Test	6.12
Side(s) or End(s) Latch Testing, or Both	6.13
Dropgate Latch Testing	6.13.1
More ASTM standard pdf ASTM E2030-06 Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings $29.00 $58.00 Add to Cart ASTM D6584-00e1 Standard Test Method for Determination of Free and Total Glycerin in B-100 Biodiesel Methyl Esters By Gas Chromatography $30.00 $60.00 Add to Cart ASTM A504/A504M-18 Standard Specification for Wrought Carbon Steel Wheels $34.00 $68.00 Add to Cart ASTM D5526-94(2002) Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions $30.00 $60.00 Add to Cart