BS 1722-10:2019

Fences-Specification for anti-intruder fences in chain link and welded mesh

BSI Group, 04/26/2019

Publisher: BS

File Format: PDF

$166.00$332.74


Published:26/04/2019

Pages:48

File Size:1 file , 1.7 MB

Note:This product is unavailable in Ukraine, Russia, Belarus

Scope: This part of BS 1722 specifies requirements for anti-intruder chain link or welded mesh fences and gates of at least 2.4 m in height for situations that require a higher level of protection than that offered by fences conforming to BS 1722-1. It also includes requirements for the installation of the fencing at the specified location. Where enhanced levels of security are required, other types of fences are specified in BS 1722-12 and in the relevant clauses of BS 1722-14.

Provision is made for either single or double extension arms.

This British Standard includes requirements for component dimensions, together with the permissible tolerances on size. These are minimum requirements and it is acceptable to use larger sizes, except where this could adversely affect the fitting of components or if replacement parts are required to match with those already present.

This British Standard includes requirements for protective treatments. However, maintenance requirements for the fence after installation are outside the scope of this standard.

This British Standard specifies the requirements for posts, steel gates and gate posts and zinc coated or plastic coated zinc coated wire or mesh infill.

This British Standard also specifies requirements for fence materials and their combination and installation. Because a fence is made up of a number of separate components of which the particular features vary, e.g. zinc coated or plastic coated wire, a number of combinations are available to the user. Annex A provides details of the fence requirements and installation site to be agreed between the fence supplier and client at the time of ordering a fence. However, as conditions vary from site to site, the information in Annex A is not exhaustive.

Ground conditions might indicate that a variation in the length of a post or strut, or the depth to which it can be set, is desirable. The post and strut setting depths specified in this part of BS 1722 are intended for use in normal ground conditions but if special conditions exist that warrant a change in the specification, e.g. the ground is softer or firmer than usual, such a change should be agreed with the specifier. This also applies to other similar changes.

Cross References:
BS EN 10244-2
BS 1722-1
BS EN ISO 9606-1
BS EN ISO 1461
BS EN 1011-1
BS 7371-6
BS EN 10223-4
BS EN 12878
BS 1722-16
BS 7371-3
BS 8500
BS EN 10088-1
BS EN 10240
BS EN ISO 2063
BS 4320
BS EN 10223-1
BS EN 10088-3
BS EN 1011-2
BS EN ISO 12944
BS EN 12620
BS EN 10223-6:2012
BS 4102:1998
BS 4-1
BS EN 10210-2
BS 1722-14
BS EN 10296-1
BS EN 10219-1
DIN 1615
BS EN 10219-2
BS EN 10210-1
BS EN 1176-1
BS EN 10025-2
BS 1722-1
BS 1722-12
BS EN ISO 14713
BS EN 10056-1
BS EN 10255
BS EN 1991-1-4
BS EN 12839:2001


All current amendments available at time of purchase are included with the purchase of this document.

More BS standard pdf

BS 06/30135306 DC

BS 06/30135306 DC

EN 12517-2. Non destructive testing of welds. Part 2. Evaluation of welded joints in aluminium and its alloys by radiography. Acceptance levels

$117.00 $235.43

BS 06/30133671 DC

BS 06/30133671 DC

EN 1176-4. Playground equipment and surfacing. Part 4. Additional specific safety requirements and test methods for cableways

$145.00 $291.08

BS 06/30134637 DC

BS 06/30134637 DC

ISO 22007-3. Plastics. Determination of thermal conductivity and diffusivity. Part 3. Temperature wave analysis method

$126.00 $253.62

BS 06/30105375 DC

BS 06/30105375 DC

BS EN ISO 3691-2. Industrial trucks. Safety requirements and verification. Part 2 . Self-propelled variable-reach trucks

$105.00 $211.01